We accept donations using either money, Bitcoin or Litecoin. Refer to Service Manual, Page 5-3 7. Install the 2 small bolts into the channel bracket on the rear muffler. In case of eye contact flush with large amounts of water and get medical attention. The procedures in this instruction sheet should be performed by one experienced in precision measuring techniques. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Set this foot peg aside as it will also need to be reinstalled.
Re-install shock spring, making sure it is locked in place with the retaining ring prior to slowly releasing the spring compressor. Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. A book in the Haynes Owners Workshop Manual Series Printed in the U. Always turn the engine off before leaving the motorcycle unattended and remove the key from the main switch. The four socket head screws fastening the radio or storage box to the left and right radio support brackets can be accessed through the oblong holes in the fairing brackets. I can't find a diagram of your carb so I am assuming there is a drain screw. Remove fuel tank according to the instructions in the service manual.
Remove and retain the button head screw on the underside of the fork stem and bracket assembly that holds the brake line manifold tee. Install modified top center screw 1093 between the cylinders and tighten to 50-90 in-lbs 5. Located near rear turn signals Use new bolts provided. Information on the troubleshooting, servicing specification lists, tightening torque, checking and adjusting, disassembling and assembling and servicing which cover procedures, precautions, factory specifications and allowable limits. Using the manual The manual is divided into Chapters. Remove the air cleaner box.
Install the new wheel to the rear fork. It has plenty of good parts on it. These groups contain general information, diagnosis, testing, adjustments, removal, installation, disassembly, and assembly procedures for the systems and components. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Note: Center stand sop bracket in provided in the hardware kit and is approx. Stored indoors winters yes, inside the house.
Newly Painted Frame and Wheels. Check all of the bolts that you have installed of removed to insure that they are tight. Re-assemble all saved components to the new chrome rear wheel assembly. Custom wire harnessDigital speedometer and tachometer. Do not re-use brake disc screws. Category Cruiser Motorcycles Engine 920 Posted Over 1 Month I have for sale a Midnight Virago Motorcycle Black.
Remove the front seat and disconnect the battery. Then remove the rear nut on the same foot peg. Used parts can be obtained for roughly half the price of new ones, but you can't always be sure of what you're getting. Good luck and have a nice day. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg.
Follow up by thoroughly wiping affected area with a clean, damp, soft cloth small spills or washing with a large quantity of soapy water large spills. Torx screw 5 replace 7. Allow shock spring to expand against the retaining ring and machined washer. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Ask a Harley-Davidson dealer about the selection of Genuine Motor Accessory Custom Braided Clutch Cables and Brake Lines that are available. Remove existing air cleaner assembly. Feel free to contact me with any questions or to schedule an inspection.
Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Cover the throttle bodies to prevent anything from dropping into the engine. We've done all the hard work. When it's necessary to refer to another Chapter, the reference will be given as Chapter and Section number. To perform all repairs listed in this manual, a complete set of standard tools, as well as the special tools and fixtures shown and listed are necessary.
Tank and Electrical Box ready for your custom paint job. Right floorboard this can be simply loosened, by loosening the two bolts underneath With the above parts removed, you can remove the Allen bolts holding the beauty cover and filter cap from your engine. Engine Guard Saddlebag Guards Garage Kept One Owner Well Maintained Clean Title Comes with: Stock parts if you want to remove the tour pack Extra Clutch Cable Two full sets of keys Original Owner's Manual Missing one front turn signal lens - temporarily replaced with original lens. Whether buying new, used or rebuilt parts, the best course is to deal directly with someone who specializes in parts for your particular make. References to the left or right side of the vehicle assume you are sitting on the seat, facing forward. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity.