Remove the screws B and pull the entire light unit out. Have the tire replaced or repaired at an authorized Mitsubishi Motors dealer or a repair N00849600298 facility of your choice as soon as possible. The wrong tire pressure will wear rate of the tire when tested under controlled conditions cause problems in three major areas: on a specified government test course. Avoid hard braking and high speeds, and contact an authorized Brake warning light Mitsubishi Motors dealer or a repair facility of your choice for assis- tance. To reduce side glare, turn the visor to the side 2. On vehicles equipped with Mitsubishi Multi-Communica- tion System, screen operations can be used to make the adjustment. N00944000331 Back-up light Tail light 1.
Wash thor- Good oughly after working with it. The warning may display even if the F. Lightly press the multi-information meter 1. Check that the cooling fan is running. The kerb weights related specifications are not applicable for use in Sweden; the correct weights are stated in the registration book of the vehicle.
Cup holder for rear seat p. For vehicles equipped with turbocharger, when replacing 3. See your authorized Mitsubishi Motors dealer for details. The following information is included on the multi-information display: warnings, odometer, tripmeter, service reminder, engine coolant temperature, fuel remain- ing, outside temperature, selector lever position, average and momentary fuel consumption, driving range, average speed and meter illumination. Change to 11:00 and signal interference.
Rotate the jack by hand until the flange por- tion B fits in the groove C at the top of the jack. Keep sparks, cigarettes, and flames away from the Battery terminals and related accessories contain battery because the battery could explode. Rotate the jack by hand until the flange portion B fits in 4. All the keys have to be re-reg- does not start, we recommend you to con- istered in the immobilizer computer unit. E00600101021 E00600200067 For economical driving, there are some technical re- Driving after drinking alcohol is one of the most fre- Avoid driving at full speed.
To install the bulb, perform the removal steps in reverse. For vehicles equipped with the Mitsubishi Multi-Commu-. However, you can add to the future performance and economy of your vehicle by observing the following precautions during the first 300 miles 500 km. See the following section for the types of connecta- ble devices and supported files. Remove the bulb by pulling it out. The trailer weights related specifications are not applicable for use in Switzerland. Charging system deals with alternator that keep the battery charged at constant level.
To close the vent, move the knob to the inside as far as possi- ble. To preserve and protect, use a leather protecting agent on Such products, when applied to the instrument panels or the genuine leather surface. Mitsubishi Motors dealer or a repair facility of power supply error Power supply error of external device. You can personalize the air selection switch and air conditioning switch to match your personal preferences. After checking that the door is locked, turn the key back to the To lock or unlock all doors, use the power door lock center and remove it. To select the desired sound field.
Motors dealer or a repair facility of your choice to have the system checked. At the and the interior intrusion detection function vehicles end of that period, the alarm will automatically shut off to equipped with the interior alarm sensor save battery power. Turn the emergency key with the F. N00515200148 After using the emergency key, be sure to reinsert it into The emergency key is built into the F. Never use a fuse with a capacity greater than the one listed or any substitute, such as wire, foil etc. For N00510500133 details, refer to a separate operation manual.
Electric remote-controlled outside rear-view mirrors switch p. To adjust the vertical mirror position It is possible to move the mirror up and down to adjust its posi- tion. Mitsubishi Outlander use a 4-spoke type steering wheel with a shock absorbing and tilt steering mechanism. Remove the wheel nuts with the wheel nut tyre is raised slightly off the ground surface. Exterior is covered by Outlander service guide in subgroup 51. The trailer weights related specifications are not applicable to use in Norway; the correct maximum weights are stated in the registration book of the vehicle. Use this mode for The selected control mode is stored in memo- under aggressive driving conditions.
Therefore, the operation sound of the cooling fans may be Do not run the engine at high speeds for example, heard even after the engine is stopped. A text message will appear on the display. In this case, the air conditioning indi- cator will not change. Screen type 1 Screen type 2 System operation status Reference When the Active Stability Control. The autochanger will select the lowest-numbered empty slot and switch to loading standby mode. Repeated continuous operation between lock and unlock could activate the power door locking systems built-in protection circuit and prevent the system from operating.