Inlet exhaust gas temperature sensor - 5. Proceed as follows, by acting from inside the cab see figure Figure 3 unscrew and remove knob 1 ;. Throttle valve assembly - 3. Figure 72 Figure 69 75269 Take off the gasket 1 and remove the hydraulic tappets together with the rocker arms 2. Diesel oil inlet - 4. Fit the thermostat casing 2 with a new seal and tighten the fixing screws 3 to the prescribed torque.
Disconnect: - vacuum pipe 27 from the E. Diesel oil inlet - 8. Connect the coolant pipes by securing them with the new Connect pipe 5 to pipe union 7 , then secure it with a new clamps :. Fuel pressure sensor - 7. Air bleeding or water draining screw - 11. Afterwards, the - fuel pre-filter high-pressure pump correctly supplies the hydraulic - electric supply pump accumulator. Also, I think the figures earlier are mixed up, pretty sure its: 3500 gross vehicle weight 6300 gross train weight 7000 gross train weight followed by the front and rear axle weights.
Remove the hydraulic chain tightener: top 1 and lower 2. Mount the cylinder head 1. It must be ensured that the mounting brackets can not move. Not sure on the towing limits for the older 2. Produce a certified copy of the above-mentioned document Agenzia Effe will complete the practice only when received: the certified copy of the Report, of the documentation requested to the tenderer, and the payment. Electronic central unit - 2. Diesel oil filter - 5.
Usually, there are no additional components which could interfere with installing the kits in this space. Replace the cup plugs if they are found to leak at oil, using a suitable drift for their removal —. Pull out the centrifugal filter 1. For your safety and to prevent possible damage to your vehicle, do not exceed the maximum load recommended by the vehicle manufacturer. Disconnect the electrical connection 1 from the sensor on 52238 the clutch pedal and the electrical connection 4 from the Set a proper container under the brake pipes 4 and remove. Figure 115 75290 Take out the couplings 1 and remove the oil jets 2.
Remove the screws 4 and the lower fixed skid 3. Engine coolant temperature sensor - 4. Fit the gasket 4 and the frame 3 onto the oil sump 1. In case of coolant 543212 Electromagnetic pulley leaking from the seal or damage, it must be replaced. This kit does not increase the G. Take out the screws 2 and remove the engine flywheel 1. The donation will be processed per the By submitting the one time charge, I am agreeing to make a one-time donation to the forum.
Production date Electrical injectors are not assigned any more to classes Min 01 - Med 02 - Max 03 ;. Moreover, the following Place the vehicle on a pit or auto lift. Oil filter with single filtration with built-in by-pass valve —. Friction seals worn due to off centring of the driven disk. The behaviour that could lead to this kind of trouble is well known.
Vacuum pump coupling - 6. Using the extractor 99340028 2 extract the toothed pulley Fit the thermostat casing 2 with a new seal and tighten the 1 driving the camshaft. It comprises the following parts: - An expansion tank whose plug has two valves incorporated in it: an outlet and an inlet, which govern the pressure of the system. Pipes connecting pressure sensor to catalyst - 7. Make sure that the cut-out in the support of the upper bracket is pointing in board and towards the front of the vehicle. Disconnect pipe 13 from the heat exchanger and the throttle valve assembly.
Sliding sleeves positioning springs yielded or broken. Intake valve camshaft seats — 2. Inlet air temperature sensor - 7. Throttle valve assembly - 3. Remove the screws 1 and the shoulder plate 2. Take out the screw 2 and remove the speed sensor 1. Flow meter body - 3.
Also consider the van, a van, a van, a van, a van, a van,a van, a van or a van. Fit the drive ring 5 on the flexible belt 3 and fasten the ring on the compressor support. Figure 104 Figure 107 88282 88279. Attach the lower bracket to the axle using the axle straps with the M10X50 bolts, M10 locknuts and M10 washers. Before fitting a new driven disk check that it is centred as follows: Position the driven disk 1 on a lathe and, with the use of a. I understand that as long as the towing vehicle is under 3.
Compare the load and elastic deformation data with those of the new springs given in the following figures. Camshaft on exhaust side — 4. These could be jammed or damaged while assembling the kit. Take out the screws 1 and remove the overhead 2. In case of coolant Figure 301 leaking from the seal or damage, it must be replaced. Checking connecting rod Figure 139 61695 Check the bending of the connecting rod 5 by comparing.